ss-440440C Stainless steel is a type of modern steel and famous for its high corrosion resistant, wear resistance, strength and hardness qualities, among all the stainless alloys, capable of attaining (after heat treatment) the highest hardness (60 HRC). It has good resistance to the atmosphere, fresh water and mild acids. It has best resistance in the hardened, tempered and passivated condition. It allows creating a smooth polished surface and Razor sharp edges. It is being used in cutting instruments, rolling element bearings, valve seats, high quality knife blades, surgical instruments, chisels, ball bearings and valve parts and most commonly used in the production of Cutting tools, including Haircutting Scissors, daggers and swords.

Grades 440A and 440B are identical except for slightly lower carbon contents (0.60 – 0.75% and 0.75 – 0.95% respectively), they attain lower hardness but have slightly higher corrosion resistances. Although all three versions of this grade are standard grades, in practice 440C is more available than the A or B variants.

Another alloy 440F (UNS S44020) also exists, with the same high carbon content as 440C.

440 Steel family, there is a new modern kind of steel, known as 440V steel. Basically, it is the advancement of 440C steel. This steel has same level of hardness like 440C, but it has more corrosion resistant ability and more machine-ability.

Heat Resistance:

Not recommended for use in temperatures above the relevant tempering temperature, because of reduction in mechanical properties by over-tempering.

Heat Treatment:

Annealing – Full anneal – 850-900C, slow furnace cool to about 600C and then air cool. Sub-critical Annealing – 735-785C and slow furnace cool.

Hardening – Heat to 1010-1065C, followed by quenching in warm oil or air. Oil quenching is necessary for heavy sections. Immediately temper at 150-370C to obtain a wide variety of hardness values and mechanical properties as indicated in the accompanying table.

Tempering in the range 425-565C is to be avoided because of reduced impact resistance and corrosion resistance. Tempering in the range 590-675C results in lower hardness (the product become machinable) and high impact resistance.

Welding

If welding is necessary pre-heat at 250C and follow welding with a full anneal. Grade 420 filler will give a high hardness weld (not as high as the 440C). Generally welding of 440C is not recommended due to its hardening capability which can lead to the formation cracks within or near the weld.

Machining

In the annealed condition this grade is relatively easily machined; approximately the same as for high speed steel. If this grade is hardened machining becomes very difficult and probably impossible.

Composition

Chemical Composition ranges of 440C stainless steel

Grade440C
Ingredients Min. Max.
Carbon 0.95 1.20
Manganese 1.00
Silicon 1.00
Phosphorus 0.040
Sulphur 0.030
Chromium 16.00 18.00
Molybdenum 0.75
Iron Balance

 

440C Physical Properties

Physical properties for grade 440 stainless steels.

Grade Density (kg/m3) Elastic Modulus (GPa) Mean Coefficient of Thermal Expansion (mm/m/C) Thermal Conductivity (W/m.K) Specific Heat
0-100C (J/kg.K)
Electrical Resistivity (nW.m)
0-100C 0-200C 0-600C at 100C at 500C
440A/B/C 7650 200 10.1 10.3 11.7 24.2 460 600

 

440C Related Specifications

USA Germany Japan Australia
ASTM A276-98b 440C
SAE 51440C AISI 440C
UNS S44004
W.Nr 1.4125 X105CrMo17 JIS G4303 SuS 440C AS 2837-1986 440C